ZTE ZXHN h398N DIGI Router – How to Factory Reset. Роутер zte zxhn h298n настройка


ZTE ZXHN h398N DIGI Router

ZTE ZXHN h398N DIGI Router Reset To Factory Defaults. You can easily reset your wireless WiFi router.  Here we are also provide Reboot methods of ZTE routers. You must reset your Wireless router to the factory defaults settings if you have forgotten your router user name or password. And you need to reboot your device if your router does not works properly.

 

This post will detail how to reset back to a factory default configuration the ZTE ZXHN h398N DIGI. If password have been forgotten and or access to the ZTE Router is limited or configurations have been done incorrectly, resetting back to the factory default settings can assist. And also provide How to change router wireless password.

 

 

Difference between Reset and Reboot :

There is a big difference between Resetting a router and Rebooting a router. Reboot means, cycle the power to Router or Refresh the router. Resetting involves changing the router settings back to its factory defaults. Perhaps you have forgotten the password of your ZTE router and now you want to reset the password. First you need to Hard Reset the Router then you can use the default password to access your router.

 

When you reset your router the following settings will be changed:

  • ZTE Router username and password
  • Wi-Fi username and password
  • ISP ip addresses and DNS
  • Any firewall settings you have made
  • Any portforwards you have set up
  • Generally, any configuration or settings changes that you have made to your router.

 

 

How To Reset ZTE ZXHN h398N DIGI Router With Button :

To perform a factory reset, please follow Below steps.

  • Power on the ZTE Router, place a paper clip or Pin into the hole on the back of the Router labeled Reset.
  • Hold paper clip or pin down for 10 to 15 seconds and release.
  • The Router will reboot on its own. Once the WLAN light stops blinking, the Router is reset.
  • Please Note, Resetting the ZTE router does not reset the firmware to an earlier version. It will only change all settings back to factory defaults.

 

 

ZTE ZXHN h398N DIGI Default Login, Password and IP :

Once your ZTE router has been reset, it goes back to it’s factory defaults Settings.

  • IP address: 192.168.0.1
  • Username: admin
  • Password: admin
  • OR see back side of your device.

 

 

How To Reset ZTE ZXHN h398N DIGI Router From Admin Control Panel  :

You need to know the Internal IP Address of your ZTE ZXHN h398N DIGI router before you can login to it. We are already placed Login details above clearly. The ZTE ZXHN h398N DIGI has a web interface for configuration. You can use any web browser (Firefox and Chrome) to login to the Router. First connect your router to PC with RJ45 Cat5 or Cat6 cable. Then login with above Credentials. After login follow below steps to Reset your device.

 

Not available

 

Note : If you can not get logged in to your Wireless router, here a few possible solutions you can try.

Forgot Password to ZTE ZXHN h398N DIGI Router :  If your Internet Service Provider or ISP supplied you with your router then you might want to try giving them a phone call and see if they either know what your ZTE router’s username and password are, or maybe they can reset it for you.

How to Reset the ZTE ZXHN h398N DIGI Router To Default Settings : If you still can not get logged in then you are probably going to have to Hard reset your router to its default settings. Please read starting portion of this page.

 

 

How to Reboot your ZTE Router :

Rebooting a router means cycling the power to it or refresh the router. If you want to reboot your router, follow below steps.

Method 1 :

  • Unplug the power connector from the back of the ZTE router and plug it back in.
  • Wait above 20 seconds for the router to reboot.
  • Your internet connection may be drop when your wireless router is rebooted. If someone is using a computer on your network to access the internet, you may want to warn them.

 

 

ZTE Customer Support :

If you are still having problems, contact ZTE customer care department. Follow below links.

 

Customer Support (For Global Users)

 

www.hardreset99.com

ZTE ZXHN h398N Hyperoptic Router

ZTE ZXHN h398N Hyperoptic Router Reset To Factory Defaults. You can easily reset your wireless WiFi router.  Here we are also provide Reboot methods of ZTE routers. You must reset your Wireless router to the factory defaults settings if you have forgotten your router user name or password. And you need to reboot your device if your router does not works properly.

 

This post will detail how to reset back to a factory default configuration the ZTE ZXHN h398N Hyperoptic. If password have been forgotten and or access to the ZTE Router is limited or configurations have been done incorrectly, resetting back to the factory default settings can assist. And also provide How to change router wireless password.

 

 

Difference between Reset and Reboot :

There is a big difference between Resetting a router and Rebooting a router. Reboot means, cycle the power to Router or Refresh the router. Resetting involves changing the router settings back to its factory defaults. Perhaps you have forgotten the password of your ZTE router and now you want to reset the password. First you need to Hard Reset the Router then you can use the default password to access your router.

 

When you reset your router the following settings will be changed:

  • ZTE Router username and password
  • Wi-Fi username and password
  • ISP ip addresses and DNS
  • Any firewall settings you have made
  • Any portforwards you have set up
  • Generally, any configuration or settings changes that you have made to your router.

 

 

How To Reset ZTE ZXHN h398N Hyperoptic Router With Button :

To perform a factory reset, please follow Below steps.

  • Power on the ZTE Router, place a paper clip or Pin into the hole on the back of the Router labeled Reset.
  • Hold paper clip or pin down for 10 to 15 seconds and release.
  • The Router will reboot on its own. Once the WLAN light stops blinking, the Router is reset.
  • Please Note, Resetting the ZTE router does not reset the firmware to an earlier version. It will only change all settings back to factory defaults.

 

 

ZTE ZXHN h398N Hyperoptic Default Login, Password and IP :

Once your ZTE router has been reset, it goes back to it’s factory defaults Settings.

  • IP address: 192.168.0.1
  • Username: admin
  • Password: admin
  • OR see back side of your device.

 

 

How To Reset ZTE ZXHN h398N Hyperoptic Router From Admin Control Panel  :

You need to know the Internal IP Address of your ZTE ZXHN h398N Hyperoptic router before you can login to it. We are already placed Login details above clearly. The ZTE ZXHN h398N Hyperoptic has a web interface for configuration. You can use any web browser (Firefox and Chrome) to login to the Router. First connect your router to PC with RJ45 Cat5 or Cat6 cable. Then login with above Credentials. After login follow below steps to Reset your device.

 

Not available

 

Note : If you can not get logged in to your Wireless router, here a few possible solutions you can try.

Forgot Password to ZTE ZXHN h398N Hyperoptic Router :  If your Internet Service Provider or ISP supplied you with your router then you might want to try giving them a phone call and see if they either know what your ZTE router’s username and password are, or maybe they can reset it for you.

How to Reset the ZTE ZXHN h398N Hyperoptic Router To Default Settings : If you still can not get logged in then you are probably going to have to Hard reset your router to its default settings. Please read starting portion of this page.

 

 

How to Reboot your ZTE Router :

Rebooting a router means cycling the power to it or refresh the router. If you want to reboot your router, follow below steps.

Method 1 :

  • Unplug the power connector from the back of the ZTE router and plug it back in.
  • Wait above 20 seconds for the router to reboot.
  • Your internet connection may be drop when your wireless router is rebooted. If someone is using a computer on your network to access the internet, you may want to warn them.

 

 

ZTE Customer Support :

If you are still having problems, contact ZTE customer care department. Follow below links.

 

Customer Support (For Global Users)

 

www.hardreset99.com

Setup WiFi on the ZTE ZXHN h398N DIGI

The ZTE ZXHN h398N DIGI router is considered a wireless router because it offers WiFi connectivity. WiFi, or simply wireless, allows you to connect various devices to your router, such as wireless printers, smart televisions, and WiFi enabled smartphones.

Other ZTE ZXHN h398N DIGI Guides

WiFi Terms

Before we get started there is a little bit of background info that you should be familiar with.

Wireless Name

Your wireless network needs to have a name to uniquely identify it from other wireless networks. If you are not sure what this means we have a guide explaining what a wireless name is that you can read for more information.

Wireless Password

An important part of securing your wireless network is choosing a strong password.

Wireless Channel

Picking a WiFi channel is not always a simple task. Be sure to read about WiFi channels before making the choice.

Encryption

You should almost definitely pick WPA2 for your networks encryption. If you are unsure, be sure to read our WEP vs WPA guide first.

Login To The ZTE ZXHN h398N DIGI

To get started configuring the ZTE ZXHN h398N DIGI WiFi settings you need to login to your router. If you are already logged in you can skip this step.

To login to the ZTE ZXHN h398N DIGI, follow our ZTE ZXHN h398N DIGI Login Guide.

Find the WiFi Settings on the ZTE ZXHN h398N DIGI

If you followed our login guide above then you should see this screen.

The wireless setup guide for the ZTE ZXHN h398N DIGI router starts on the Status page. To begin configuring your wireless settings, click Network located in the left hand sidebar. After that, click WLAN and then SSID Settings below that.

Change the WiFi Settings on the ZTE ZXHN h398N DIGI

You should be taken to the page you see above.

Start off by opening the Choose SSID drop down list and selecting SSID1.

After that, in the box labeled SSID Name, enter your desired network name. This can be whatever you like, however we strongly suggest avoiding any kind of personal information. For more on this subject, take a look at our Wireless Names Guide.

Make sure to click Submit before moving on.

Now click Security on the left hand side of the page.

On this new page, start by again opening the drop down menu marked Choose SSID and selecting the SSID you just created.

Following that, be sure that the Authentication Type is set to WPA2-PSK. Why is this important? Read our WEP vs. WPA Guide to find out.

Now you need to set a WPA Passphrase. A strong passphrase can be difficult to come up with, however a good starting point is to keep it 14-20 characters in length and avoid any personal information. For more helpful tips, check out our Choosing a Strong Password Guide.

Finally, set the WPA Encryption Algorithm to AES.

Congratulations! That's all there is to it. Just make sure to click Submit before closing the page.

Possible Problems when Changing your WiFi Settings

After making these changes to your router you will almost definitely have to reconnect any previously connected devices. This is usually done at the device itself and not at your computer.

Other ZTE ZXHN h398N DIGI Info

Don't forget about our other ZTE ZXHN h398N DIGI info that you might be interested in.

Written by Rachel Bauer
Rachel Bauer is an owner and primary author for SetupRouter.com. She is available on Google+ and you can find more of her articles in the Networking section of our site.

setuprouter.com

How to Login to the ZTE ZXHN h398N Hyperoptic

This page shows you how to login to the ZTE ZXHN h398N Hyperoptic router.

Other ZTE ZXHN h398N Hyperoptic Guides

Find Your ZTE ZXHN h398N Hyperoptic Router IP Address

We need to know the Internal IP Address of your ZTE ZXHN h398N Hyperoptic router before we can login to it.

ZTE ZXHN h398N Hyperoptic IP Addresses
192.168.1.1

If you did not see your router's ip address in the list above. There are 2 additional ways that you can determine your router's IP address:

  1. You can either follow our How To Find Your Routers IP Address guide.
  2. Or you can use our free software called Router IP Address.

Now that you have your router's Internal IP Address we are ready to login to it.

Login to the ZTE ZXHN h398N Hyperoptic Router

The ZTE ZXHN h398N Hyperoptic has a web interface for configuration. You can use any web browser you like to login to the ZTE ZXHN h398N Hyperoptic. In this example we'll use Internet Explorer.

Enter ZTE ZXHN h398N Hyperoptic Internal IP Address

Put the Internal IP Address of your ZTE ZXHN h398N Hyperoptic in the Address Bar of your web browser. It looks like this:

Then press the Enter key on your keyboard. You should see a dialog box pop up asking your for your ZTE ZXHN h398N Hyperoptic username and password.

ZTE ZXHN h398N Hyperoptic Default Username and Password

You need to know the username and password to login to your ZTE ZXHN h398N Hyperoptic. All of the default usernames and passwords for the ZTE ZXHN h398N Hyperoptic are listed below.

ZTE ZXHN h398N Hyperoptic UsernamesZTE ZXHN h398N Hyperoptic Passwords
located on the back of the HyperHublocated on the back of the HyperHub
adminpassword

Enter your username and password in the dialog box that pops up. It looks like this:

ZTE ZXHN h398N Hyperoptic Home Screen

You should now see the ZTE ZXHN h398N Hyperoptic Home Screen, which looks like this.

If you see this screen, then congratulations, you are now logged in to your ZTE ZXHN h398N Hyperoptic. You are now ready to follow one of our other guides.

Solutions To ZTE ZXHN h398N Hyperoptic Login Problems

If you can not get logged in to your router, here a few possible solutions you can try.

ZTE ZXHN h398N Hyperoptic Password Doesn't Work

You should try other ZTE passwords. We have a large list of ZTE Passwords that you can try located here. Perhaps your router's default password is different than what we have listed here.

Forgot Password to ZTE ZXHN h398N Hyperoptic Router

If your Internet Service Provider supplied you with your router then you might want to try giving them a call and see if they either know what your router's username and password are, or maybe they can reset it for you.

How to Reset the ZTE ZXHN h398N Hyperoptic Router To Default Settings

If you still can not get logged in then you are probably going to have to reset your router to its default settings. You may want to follow our guide called How To Reset your Router.

Other ZTE ZXHN h398N Hyperoptic Guides

Here are some of our other ZTE ZXHN h398N Hyperoptic info that you might be interested in.

Written by Rachel Bauer
Rachel Bauer is an owner and primary author for SetupRouter.com. She is available on Google+ and you can find more of her articles in the Networking section of our site.

setuprouter.com

router - Wireless bridge between ZTE ZXHN h398N and WAG320N

(Edit) I answered the question first and when re-reading, I realized that wireless part of the question is in the title so I looked into that also.

Specifically about the "wireless bridge":

In summary, not possible with specifically the gear you have.

Here is why I say this: - the ZTE is made as a base station. The documentation is fairly poor. It does not seem to have the features necessary to be a repeater.

The linksys does not support the wireless repeater feature.

A repeater would be the technical term for what you describe as a "wireless bridge" with only 2 access points that both allow additional wireless connections. Your ZTE is already acting as a "wireless bridge/switch" by itself. If you want the Lynksys router as a "wireless bridge" with dhcp properly managed on one network, you want the functionality of a repeater.

I can see you doing this if either of the machines can be a repeater, or you could do that with a linux box and wireless usb cards by hand with care about dhcp server addressing. I've gone through the manuals of both devices and if using either device as an access point is possible, it is hidden or undocumented.

The best solution would be to buy a repeater (or other gear), or possibly hacking the modem with little chance of success, which is fairly advanced and not the question either.

Nevertheless, I will give you some info on making a lan bridge and links to some documents I reviewed.

Here is the main documentation site for the zte model.

The best manual I found was the maintenance manual ( Which is actually a user manual ) titled:

1 ZXHN h398N Broadband Access CPE (V1.1) Home Gateway Maintenance Manual (2FX + 1USB).pdf

at the following site:

http://enterprise.zte.com.cn/en/products/network_lnfrastructure/cpe/broadband/201404/t20140418_422573_6402.html

Answering the question as realistically as possible:

If you want everything on the same network, let's go with the one from the router connected to the ISP, and only make adjustments to the Linksys WAG320N. This avoids any complications with your externally-facing equipment that might technically not be your property or that has ISP-specific limitations. In principle the solution could apply to either router but adjusting the Linksys WAG320N is the logical approach from what I understand of the question.

I want to have all devices on the same network. How should I set it up?

The ideal answer is to simply turn the Linksys WAG320N into an access point. That feature does not seem to be available for that device.

Answer 1)

lan-to-lan cascading

What you are trying to do seems to be what Linksys calls lan-to-lan cascading. Please look at the following Linksys document for instructions. Your Linksys WAG320N would be the "secondary router" in the instructions.

http://www.linksys.com/ca/support-article?articleNum=132275

Answer 2)

By only having one network, one dhcp server and only using one WAN port.

(There are no guest networks in the question.)

If you can turn off dhcp on the Linksys WAG320N:

Turn off dhcp and do not use the WAN port.

I did not see how to do that by reviewing the site and I do not have the device with me.The virtual configuration menu on the Linksys site seems to have moved.

I would use this solution over the other one if possible.

If you cannot change dhcp settings on the Linksys WAG320N:

This solution might work: Put the device in bridged mode and do not use the connection labeled "WAN". All this should do is disable dhcp.

Step 1: Access the web-based setup page.

Step 2: On the Basic Setup sub-tab, set Encapsulation to Bridged Mode Only.

The steps are outlined at the following Linksys website. The page includes many more steps because it describes bridged mode in terms of being bridged directly to your ISP. Those steps are not necessary as you are not using the wan port on that device. We just want turn turn on the feature to stop the dhcp server. The remaining steps on that page are not important. http://www.linksys.com/us/support-article?articleNum=137299

superuser.com

ZXHN h268N

Modeminizin WEB ara yüzünde girmek için öncelikle modem ile tüm kablo bağlantılarınızın doğru şekilde yapıldığından ve modeminizin çalıştığından emin olun, daha sonra bilgisayarınızda bir Internet Explorer penceresi açın ve adres alanına 192.168.2.1 (modemin IP adresi) girerek enter tuşuna basın.

Karşınıza modem ara yüzüne girmek için sizden kullanıcı adı ve parolası istenecek.

Fabrika verisi olarak modem ara yüzü erişimi Kullanıcı Adı:admin Şifre:ttnet olarak belirlenmiştir. Eğer modem ara yüz şifresini bir başka şifre ile değiştirmediyseniz bu bilgileri girerek modem ara yüzüne girebilirsiniz.

Modem ara yüzü şifre sorgu penceresi  görüntülenmiyor ve modem ara yüzüne erişemiyorsanız;

1-)Bilgisayarın IP adresi yanlış

Bilgisayarınızın IP bilgilerini kontrol etmek için

XP işletim sisteminde

Başlat/Ayarlar/Ağ Bağlantıları bölümünde ağ kartı simgesine sağ klik Durum seçeneğini seçin.

Açılan pencerenin  üst bölümündeki Destek tabına girin ve IP Adresi ’nin 192.168.2.x veVarsayılan Ağ Geçidi ‘nin 192.168.2.1 olduğundan emin olun. Eğer IP ayarları bu şekilde değilse ağ kartınıza elle IP adresi verilmiş olabilir ya da Bilgisayarınız modeminizden IP alamamış olabilir.

Ağ Kartınıza Elle IP adresi verilmişse  Adres türü alanında Elle Yapılandırılmış

Olarak görüntülenir.  ekranda Genel tabında Özellikler butonunu tıklayın ve de gösterilen ekranda İnternet İletişim Kuralları(TCP/IP) seçeneğini seçip Özellikler butonuna tıklayın ve tüm seçimleri gösterildiği gibi yapın ve Tamam butonuna tıklayarak ayarları tamamlayın. Artık Bilgisayarınız modeminizden otomatik olarak bir IP Adresi alacaktır

Otomatik IP adresi alma fonksiyonu etkin ise Adres türü alanında DHCP Tarafından Atanan

Olarak görüntülenir. DHCP tarafından atanan olarak görüntüleniyor ve IP adres bilgileriniz yanlış ise

Bilgisayarınız modeminizden doğru şekilde IP adresi alamamış; Bunun için Modeminizi ve bilgisayarınızı kapatıp yeniden açın ve tekrar kontrol edin. Eğer sorun devam ediyorsa, modeminizi Fabrika ayarlarına döndürün.

Vista ve Win 7 işletim sisteminde

Masaüstünde sol alt bölümde Görev çubuğu üzerinde bulunan Ağ Kartı  ikonuna farenizle sağ tıkayın.

Açılan seçeneklerden Ağ ve Paylaşım Merkezi’ni Aç seçeneğini tıklayın  ve Ağ paylaşım ekranı görüntülenir.

Yukarıdaki ekranda  Yerel Ağ Bağlantısı linkine tıklayarak bağlantı durum penceresini açın  ve Ayrıntılar butonuna tıklayarak IP adres bilgilerinin doğruluğunu kontrol edin. Ağ kartınıza elle IP adresi vermek veya Elle verilmiş IP ayarını otomatik IP almaya çevirmek için Özelliklerbutonuna tıklayarak İnternet Protokolü sürüm 4 (TCP/IPv4) seçeneğine tıklayarak  pencereyi açın.

Ağ kartınızın modemden otomatik IP adresi alması için ayarlar gösterildiği gibi seçin ve Tamam butonu ile kaydederek çıkın.

Elle IP adresi vermek için;

Aşağıdaki IP adresini kullan ve Aşağıdaki DNS sunucu adreslerini kullan seçeneği seçilmeli ve modeminizin fabrikasyon IP ayarları olarak aşağıdaki örnekte olduğu gibi bir IP adresleri verin.

IP adres                                        :192.168.2.100

Alt ağ maskesi                            :255.255.255.0

Varsayılan ağ geçidi                  :192.168.2.1

Tercih edilen DNS sunucusu   :192.168.2.1

Bilgisayarınıza elle IP adresi vermenize rağmen modeminize hala ulaşamıyorsanız, modemi ve Bilgisayarınızı kapatıp tekrar açın, sorun devam ediyorsa modeme kablo ile bağlıysanız kullanmış olduğunuz kablonun sağlam olduğundan emin olun.

www.ztemodem.net


Смотрите также